Why Won't My SIP Account Register? A Troubleshooting Guide for Softphones and IP Phones
You have your SIP details and entered them into a softphone or desk phone, but the status still says Registration failed. Or it registers, but nobody can hear you. These are the most common problems people hit with any SIP account, and nearly all of them have simple causes.
This guide works through those causes in a sensible order, using the settings and test numbers that come with a free FreeVoIP account.
Start with the three details every device needs
Every SIP device, whatever the make, needs the same three things:
- User ID (also called username, SIP user or auth name)
- Password
- SIP server, which for FreeVoIP is always sip.transcom.net
On FreeVoIP the login or auth ID is the same as the username. If your device has separate boxes for both, put the same value in each. The only time you add the domain to the username is in apps that ask for it in one field. In Zoiper, for example, you enter username@sip.transcom.net along with your password.
Problem 1: registration is rejected
If the device reaches the server but is turned away, you will usually see an "unauthorised" or "forbidden" message (often shown as a 401 or 403 code). This almost always means the credentials don't match.
- Retype the password rather than pasting it. Pasting can add hidden spaces.
- Check upper and lower case. FreeVoIP passwords are 15 to 50 characters and must contain an uppercase letter, a lowercase letter and a number.
- Make sure you are using the details for the right line. A free account includes two SIP lines, and each has its own password.
- Check the server is exactly sip.transcom.net, with no typos or extra prefixes.
Problem 2: registration times out
A timeout means the device isn't getting a reply at all. Something between you and the server is in the way, or the device is talking on the wrong port or transport.
Check that the port and transport match. FreeVoIP's device settings use:
| Device type | Transport | Port |
|---|---|---|
| IP desk phones and ATAs | UDP (or TLS) | 5060 (UDP) or 5061 (TLS) |
| Zoiper, Linphone and similar apps | UDP (or TLS) | As above |
| MicroSIP (as FreeVoIP ships it) | TCP | Source port 5061 |
| PBX trunk (FreePBX, Asterisk, 3CX) | UDP | 5060 |
If the settings are right but it still times out, the network is the likely culprit. Office firewalls and some public Wi-Fi block SIP traffic. Try the same device on a different connection, such as mobile data. If it registers there, you know where the problem lies.
Problem 3: it registers, then drops off
A phone that shows as registered for a while and then stops receiving calls is usually a router problem. Home and office routers forget about idle connections. Once that happens, incoming calls can't find their way back to your device.
Two things help:
- Keep-alives and re-registration. FreeVoIP's tested MicroSIP setup uses a register refresh of 300 seconds and a keep-alive of 15 seconds. Most devices have similar settings.
- SIP ALG. Many routers have a feature called SIP ALG that tries to rewrite SIP traffic. It often causes more harm than good. If you have registration or audio problems, look for it in your router settings and try turning it off.
Problem 4: one-way audio or no audio
This is the classic VoIP fault. The call connects but one or both sides hear silence. The signalling worked, but the audio stream is being blocked or sent to the wrong address. NAT, the way your router shares one public address between many devices, is nearly always involved.
- Check your firewall allows the audio (RTP) traffic. FreeVoIP's MicroSIP configuration uses RTP ports 10001 to 20000.
- In MicroSIP, the shipped settings use ICE only, with STUN and TURN switched off and the STUN server field left empty. If you have been experimenting, put these back.
- Try disabling SIP ALG on the router, as above.
- Dial 4443 for a sound quality test. It quickly shows whether audio is reaching you in both directions.
Problem 5: choppy or robotic sound
Poor quality usually comes down to bandwidth or the codec, the format used to compress your voice. FreeVoIP supports G.711u (PCMU), G.729, G.722 and GSM. G.711u sounds good but needs a decent connection. On a slow or congested line a lower-bandwidth codec such as G.729 may cope better.
For desk phones and ATAs, the recommended codec order is PCMU (G.711u), then G.729, then G.722. If you are on a weak mobile signal and unsure which to choose, FreeVoIP's support team can recommend one.
Problem 6: phone menus ignore your key presses
If automated menus don't respond when you press 1 or 2, your device is sending keypad tones (DTMF) in a format the other end isn't picking up. FreeVoIP's MicroSIP settings use RFC2833. Check your device uses the same setting, then dial 4747 to test your keypad tones.
Problem 7: calls won't go out
If the phone is registered and can receive calls but outbound calls fail, check these:
- Your balance. Outbound calls to landlines and mobiles are pay-as-you-go, so an empty balance stops them. Dial *225 to hear it.
- How you dial. Don't type a "+" sign. Use 00 plus the country code for international calls.
- Your Caller ID. Dial 1-555-555-0911 to hear it read back. Leave "Hide Caller ID" disabled, because national rates only apply when a valid local Caller ID is presented.
Calls between FreeVoIP accounts are free, so you can always test a second line or a colleague's account without spending anything.
Quick reference: test numbers
| Dial | What it does |
|---|---|
| 4443 | Sound quality test |
| 4747 | Keypad tone (DTMF) test |
| 1-555-555-0911 | Reads your Caller ID back to you |
| *225 | Account balance |
| *97 | Voicemail |
The shortcut on Windows
If you are on a Windows PC and just want it to work, skip manual setup entirely. Every free account includes a pre-configured MicroSIP softphone. In My Account, open My VoIP, then Lines, and click the Windows phone link beside your line. Unzip the download and run MicroSIP.exe. It registers by itself with FreeVoIP's tested settings already filled in.
This is also a handy diagnostic tool. If MicroSIP registers on your network but your desk phone doesn't, the problem is in the phone's settings, not your account or connection.
Full make-by-make settings are on the devices page and in the setup guide.
Still stuck? Ask a person
If you've worked through the list and it still won't behave, FreeVoIP has real UK engineers on hand. From a registered FreeVoIP line, dial 81 or 83 for support. If you can't register at all, call over SIP from any softphone at 15148181@sip.transcom.net, or phone +44 1273 257 623 or freephone 0808 304 8316, Monday to Friday, 9am to 5:30pm.
Get your free SIP account
If you don't have an account yet, a free FreeVoIP account gives you instant SIP credentials, two SIP lines, free VoIP-to-VoIP calls and pay-as-you-go outbound with no contract or line rental. It works with any SIP softphone, desk phone or PBX. Create your free FreeVoIP account and have your first line registered in a few minutes.